![DJI Mini 3 Pro [image]](https://www.onedrone.com/store/image/cache/catalog/banners/dji_mini_3_pro_no_rc_-550x550w-200x120w.jpg)
-150x150h.jpg)
-1000x1000-150x150.jpg)
-150x150.png)
Search Criteria
Products meeting the search criteria
Model: failsafe
The micro failsafe is designed to return the throttle servo to a preset position in the event that radio signal is lost or the receiver battery voltage drops below a factory preset voltage (4.2V). It is recommended that half brakes be programmed as the failsafe position.
Weight (with cord) : 7 Grams..
7.90€
Ex Tax:6.48€
Brand: DJI
Model: DJI-IN2-HR
Overview
Used to mount the DJI Focus Handwheel to the remote controller, enabling a single operator to adjust Zenmuse X5S focus more easily.
In the Box
Inspire 2 - DJI Focus Handwheel Remote Controller Stand ×1
Compatibility
Inspire 2DJI Focus HandwheelDJI Focus Handwheel - Inspire 2 RC CA..
59.90€
Ex Tax:49.10€
Model: 4216cw2
Specs
Stator Size: 42x16 mm KV: 310 rpm/V Weight: 195 g
In The Box
4216 Motor CW x1..
45.90€
Ex Tax:37.62€
Model: AA-PC90
Extra Soft Power cable for Alexa Mini - lenght 50 cm, specially made for gimbals.
Original connector is XT60, but we can install some other connector too...
133.90€
Ex Tax:109.75€
Brand: Mauch Electronic
Model: MAU2-042
This cable is for the PL 2-6S series BEC"s to connect to Pixhawk 2.1 or any flight controller with Molex / Clik-Mate / 2.0mm / 6p connector.
L = 150mm ..
7.90€
Ex Tax:6.48€
Brand: Mauch Electronic
Model: MAU2-041
This cable is for the PL 2-6S series BEC"s to connect to any flight controller with DF13-6p connector.
For example:
Pixhawk 1, APM... etc.
L = 150mm ..
5.90€
Ex Tax:4.84€
Brand: Mauch Electronic
Model: MAU2-004
200A - Current / Voltage measurement sensor board, based on Allegro Hall Sensor ACS758-200U.
Voltage range is up to 20S (85V) with solder bridge open and up to 7S (30V) with solder bridge closed. Please check the maual page for more details.
This Sensor board connects directly to any Premium-Line BE..
64.90€
Ex Tax:53.20€
Brand: Mauch Electronic
Model: MAU2-016
Input 2-6S LiPo / max. 28V.
Output 2x 5.35V / 3A -> +/- 0.05V –> Ripple 10mV (0.2%) at 1.5A output current.
Inclusive LDO power supply (+5.00V +/- 0.03V) for the sensor board PL-xxx as well as PL- Sensor Hub X2 and output conector with Molex Clik-Mate 4p.
Input wrong polarity protection, as well as ..
67.90€
Ex Tax:55.66€
Brand: Mauch Electronic
Model: MAU2-002
100A - Current / Voltage measurement sensor board, based on Allegro Hall Sensor ACS758-100U.
Voltage range is up to 20S (85V) with solder bridge open and up to 7S (30V) with solder bridge closed. Please check the maual page for more details.
This Sensor board connects directly to any Premium-Line BE..
54.90€
Ex Tax:45.00€
Model: wkmpmu
Spare Wookong PMU - power unit for wookong...
115.90€
Ex Tax:95.00€
Brand: Mauch Electronic
Model: MAU2-088
Mauch Standard Line Customized cable from HS-xxx-xx Sensor Board to Pixhawk / APM
The cable is made of AWG28 silicone wires with original Hirose DF13 connectors.
The total cable length should not exceed 290mm.
The cables are "hand made" and electrical tested.
If no requested cable length is provided..
5.90€
Ex Tax:4.84€
Brand: Mauch Electronic
Model: MAU2-043
This cable is for the PL 2-6S series BEC"s to connect to any flight controller with JST-GH 6p connector.
For example:
Pixhawk 3, PixRacer... etc.
L = 150mm ..
7.90€
Ex Tax:6.48€