Brand: APD
Model: APD-PDB500
The APD PDB500 is designed for high voltage and high current applications. It consists of 8 layers of heavy copper to sustain maximum current demand whilst dissipating minimal heat. This PDB can sustain up to 125A continuous to each ESC leg. Also features 12V 3Amp and 5V 3Amp regulators with a maxim..
82.96€
Ex Tax:68.00€
Brand: Mauch Electronic
Model: MAU2-058
Mauch PC-2x15A Ideal Diode / BattShare
The PC – 2x 15A is a two-supply current sharing controller which
incorporates MOSFET ideal diodes. The diodes block reverse and
shoot-through currents during start-up and fault conditions. Their
forward voltage is adjusted to share the load current..
74.90€
Ex Tax:61.39€
Brand: Mauch Electronic
Model: MAU2-025
Input 4-14S LiPo / max. 60V.Output 2x 5.30V / 1x 5.0V / 1x 12.0V / 3A -> +/- 0.05V –> Ripple 1mV @ 1.5A output current.Inclusive LDO power supply (+5.00V +/- 0.03V) for the sensor board PL-xxx as well as PL- Sensor Hub X2/X8 and output conector with Molex Clik-Mate 4p.Blue power "ON' LED.59mm ..
229.90€
Ex Tax:188.44€
Brand: Mauch Electronic
Model: MAU2-023
Input 4-14S LiPo / max. 60V.Output 2x 5.30V / 1x 5.0V / 3A -> +/- 0.05V –> Ripple 1mV @ 1.5A output current.Inclusive LDO power supply (+5.00V +/- 0.03V) for the sensor board PL-xxx as well as PL- Sensor Hub X2/X8 and output conector with Molex Clik-Mate 4p.Blue power "ON' LED.59mm x 66mm x 13..
179.90€
Ex Tax:147.46€
Brand: Mauch Electronic
Model: MAU2-024
Input 4-14S LiPo / max. 60V.Output 2x 5.30V / 1x 12.0V / 3A -> +/- 0.05V –> Ripple 1mV @ 1.5A output current.Inclusive LDO power supply (+5.00V +/- 0.03V) for the sensor board PL-xxx as well as PL- Sensor Hub X2/X8 and output conector with Molex Clik-Mate 4p.Blue power "ON' LED.59mm x 66mm x 1..
179.90€
Ex Tax:147.46€
Brand: Mauch Electronic
Model: MAU2-022
Input 4-14S LiPo / max. 60V.Output 2x 5.30V / 3A -> +/- 0.05V –> Ripple 1mV @ 1.5A output current.Inclusive LDO power supply (+5.00V +/- 0.03V) for the sensor board PL-xxx as well as PL- Sensor Hub X2/X8 and output conector with Molex Clik-Mate 4p.Blue power "ON' LED.59mm x 48mm x 13mm / 41g w..
124.90€
Ex Tax:102.38€
Brand: Mauch Electronic
Model: MAU2-021
Input 4-14S LiPo / max. 60V. Output 5.30V / 3A -> +/- 0.05V –> Ripple 1mV @ 1.5A output current. Inclusive LDO power supply (+5.00V +/- 0.03V) for the sensor board PL-xxx as well as PL- Sensor Hub X2/X8 and output conector with Molex Clik-Mate 4p. Blue power "ON' LED. 59mm x 29mm x 13mm /..
74.90€
Ex Tax:61.39€
Brand: Mauch Electronic
Model: MAU2-059
This switch connects to any Power-Cube "V3" or 030: 2x 200A PDB and acts like an manual power on/off control.It isn't just a "switch". There is a small PCB included into the main wire which implements an current control mode, rather than a simple on/off.The switch has already an installed 3D printed..
24.90€
Ex Tax:20.41€
Brand: RFDesign
Model: RFD-P-2
Power supply for RFD Series 868, 900, 868x, 900x for Pixhawk 2If you connect direclty RFD it can burn/spike your Pixhawk cause RFD can draw to much mAmps, so you need to connect it through BEC.This is 4-6S version plug and play, but we can make it 12S too...
42.64€
Ex Tax:34.95€
Brand: RFDesign
Model: RFD-P-1
Power supply for RFD Series 868, 900, 868x, 900x for Pixhawk 1If you connect direclty RFD it can burn/spike your Pixhawk cause RFD can draw to much mAmps, so you need to connect it through BEC.This is 2-6S version plug and play, but we can make it 12S too...
41.42€
Ex Tax:33.95€
Brand: Mauch Electronic
Model: MAU2-080
This sensor hub is to connect two Standard Line (HS) current sensors in
parallel. The current of both sensors will be summarized and passed to
the FC. The voltage measurement of the LiPo packs will be collected from
both sensors and passed through the Hub to the FC. The
main purpose of this ..
43.90€
Ex Tax:35.98€
Brand: Mauch Electronic
Model: MAU2-081
3D printed enclosure for the Sensor Hub X2 The enclosure should be installed with double side tape (included). The
Sensor Hub X2 will just “click” into the bottom part and the top should
be secured with any ABS (Acetone) glue or Cyanoacrylate (super) glue. REM: It is the nature of 3D printed pa..
8.90€
Ex Tax:7.30€