![DJI Mini 3 Pro [image]](https://www.onedrone.com/store/image/cache/catalog/banners/dji_mini_3_pro_no_rc_-550x550w-200x120w.jpg)
-1000x1000-150x150.jpg)
-150x150.png)
Brand: Mauch Electronic
Model: MAU2-086
The cable is made of AWG28 silicone wires with original Hirose DF13 and MOLEX / Clik-Mate 2.0mm connectors.
The total cable length should not exceed 290mm.
The cables are "hand made" and electrical tested.
If no requested cable length is provided, then we will deliver the standard length of 200mm ..
8.90€
Ex Tax:7.30€
Brand: Mauch Electronic
Model: MAU2-082
Input 2-6S LiPo / max. 28V.
Output 5.35V / 3A -> +/- 0.05V –> Ripple 10mV (0.2%) at 1.5A output current.
Input wrong polarity protection, as well as Panasonic FM input and output capacitors to prevent burn out of the UBEC from voltage spikes.
20cm output cable with Molex / 6p / Clik-Mate 2.0mm. (To ..
26.90€
Ex Tax:22.05€
Out of stock
Brand: Mauch Electronic
Model: MAU2-005
250A – Current / Voltage measurement sensor board, based on Allegro Hall Sensor ACS758-200U.
This Sensor board connects directly to any Premium-Line BEC or Sensor Hub X2-V2.
Voltage range is up to 14S (60V) with solder bridge open and up to 7S (30V) with solder bridge closed. Please check the manual..
64.90€
Ex Tax:53.20€
Brand: Mauch Electronic
Model: MAU2-058
Mauch PC-2x15A Ideal Diode / BattShare
The PC – 2x 15A is a two-supply current sharing controller which incorporates MOSFET ideal diodes. The diodes block reverse and shoot-through currents during start-up and fault conditions. Their forward voltage is adjusted to share the load currents between su..
74.90€
Ex Tax:61.39€
Out of stock
Brand: Mauch Electronic
Model: MAU2-031
This new PC Series PDB includes two fully redundant BEC’s with POWER1 and POWER2 for the FC.
All in one PDB for Pixhawk 2.1 (The Cube) and any other flight controller via adapter cable. With integrated 2x200A hall sensor, Sensor Hub X2, 4-14S HYB-BEC and most important an main power switch with an c..
619.90€
Ex Tax:508.11€
Brand: Mauch Electronic
Model: MAU2-025
Input 4-14S LiPo / max. 60V.
Output 2x 5.30V / 1x 5.0V / 1x 12.0V / 3A -> +/- 0.05V –> Ripple 1mV @ 1.5A output current.
Inclusive LDO power supply (+5.00V +/- 0.03V) for the sensor board PL-xxx as well as PL- Sensor Hub X2/X8 and output conector with Molex Clik-Mate 4p.
Blue power "ON" LED.
59mm x..
229.90€
Ex Tax:188.44€
Brand: Mauch Electronic
Model: MAU2-024
Input 4-14S LiPo / max. 60V.
Output 2x 5.30V / 1x 12.0V / 3A -> +/- 0.05V –> Ripple 1mV @ 1.5A output current.
Inclusive LDO power supply (+5.00V +/- 0.03V) for the sensor board PL-xxx as well as PL- Sensor Hub X2/X8 and output conector with Molex Clik-Mate 4p.
Blue power "ON" LED.
59mm x 66mm x 1..
179.90€
Ex Tax:147.46€
Brand: Mauch Electronic
Model: MAU2-054
Input voltage 4-20S, max. 85V !
Power-Cube 4 / V2 with 4 outputs 3x 5.3V / 10A + 1x 12.0V / 10A
REM: The output voltage can be customized. Please mention in the required Voltage at NOTE in order, if you need a different output voltage on output 2, 3 or 4 -> Output 1 can"t be changed and must remain..
399.90€
Ex Tax:327.79€
Out of stock
Brand: Mauch Electronic
Model: MAU2-053
Input voltage 4-20S, max. 85V !
Power-Cube 3 / V2 with 3 outputs 2x 5.3V / 10A + 1x 12.0V / 10A
REM: The output voltage can be customized. Please mention in the required Voltage at NOTE in order, if you need a different output voltage on output 2, 3 -> Output 1 can"t be changed and must remain 5.3V..
319.90€
Ex Tax:262.21€
Brand: Mauch Electronic
Model: MAU2-017
Input 4-6S LiPo / max. 28V.
Output 2x 5.35V / 3A + 1x 12.0V / 3A -> +/- 0.05V –> Ripple 10mV (0.2%) at 1.5A output current.
Inclusive LDO power supply (+5.00V +/- 0.03V) for the sensor board PL-xxx as well as PL- Sensor Hub X2 and output conector with Molex Clik-Mate 4p.
Input wrong polarity protec..
94.90€
Ex Tax:77.79€
Brand: Mauch Electronic
Model: MAU2-010
This sensor hub is to connect two PL-xxx current sensors in parallel. The current of both sensors will be summarized and passed to the FC. The voltage measurement of the LiPo packs will be collected from both sensors and passed through the Hub to the FC.
The main purpose of this hub is to replace ex..
54.90€
Ex Tax:45.00€
Brand: Mauch Electronic
Model: MAU2-003
200A - Current / Voltage measurement sensor board, based on Allegro Hall Sensor ACS758-200U.
Voltage range is up to 20S (85V) with solder bridge open and up to 7S (30V) with solder bridge closed. Please check the maual page for more details.
This Sensor board connects directly to any Premium-Line BE..
56.90€
Ex Tax:46.64€