![DJI Mini 3 Pro [image]](https://www.onedrone.com/store/image/cache/catalog/banners/dji_mini_3_pro_no_rc_-550x550w-200x120w.jpg)
-150x150h.jpg)
-1000x1000-150x150.jpg)
-150x150.png)
Model: HM-SB
HiModel 6-50V Input 20A Large Current Switching Mode Voltage Regulator/ SBEC
HiModel 20A SBECInput: 6 - 50.4 VOutput voltage: 7.4V 8.4V 9V 12V OUTPUT (jumper selection)Current: 20amps continuous/ 25amps peak (2 seconds)Mode: Switch-modeQuiescent current: 60uA to 200uASize: 45 x 26 x 8mmWeight: 30g..
36.90€
Ex Tax:30.25€
Model: KW-BEC-6S
High Quality, small and light 5V/12V 3A UBEC Support 2-6S/3-6S Lipo Battery Fully Shielded Anti-interference Voltage Stabilizer in Alu housing
Move switch on the side, switch between two output voltages: 5V or 12V
Input voltage: 7-28V (2-6S)Current output: 3AOutput voltage: 5V/12V (switch)Operating ..
14.90€
Ex Tax:12.21€
Brand: Gremsy
Model: GR-P-UBEC
A switching power supply that has dual outputs (12V-5A) and accept wide input range from 14V to 52V, comes in a small and lightweight module. This UBEC should be used with the PIXY where power for Flir Duo Pro R via the AUX 8-pin cable on the tilt cage. ..
81.90€
Ex Tax:67.13€
Brand: Mauch Electronic
Model: MAU2-031
This new PC Series PDB includes two fully redundant BEC’s with POWER1 and POWER2 for the FC.
All in one PDB for Pixhawk 2.1 (The Cube) and any other flight controller via adapter cable. With integrated 2x200A hall sensor, Sensor Hub X2, 4-14S HYB-BEC and most important an main power switch with an c..
619.90€ (From 16.48€ monthly)
Ex Tax:508.11€
Model: HK-SB-12S
The all new Multistar twin output SBEC is an advanced switching DC-DC regulator designed specifically with multirotors in mind.It will simultaneously supply a constant 5Amps at 5V and 10Amps at 12V. It works with 2-13 cell lipoly packs and supplies an interference free constant 5V to your receiver a..
36.90€
Ex Tax:30.25€
Brand: Mauch Electronic
Model: MAU2-025
Input 4-14S LiPo / max. 60V.
Output 2x 5.30V / 1x 5.0V / 1x 12.0V / 3A -> +/- 0.05V –> Ripple 1mV @ 1.5A output current.
Inclusive LDO power supply (+5.00V +/- 0.03V) for the sensor board PL-xxx as well as PL- Sensor Hub X2/X8 and output conector with Molex Clik-Mate 4p.
Blue power "ON" LED.
59mm x..
229.90€
Ex Tax:188.44€
Brand: Mauch Electronic
Model: MAU2-024
Input 4-14S LiPo / max. 60V.
Output 2x 5.30V / 1x 12.0V / 3A -> +/- 0.05V –> Ripple 1mV @ 1.5A output current.
Inclusive LDO power supply (+5.00V +/- 0.03V) for the sensor board PL-xxx as well as PL- Sensor Hub X2/X8 and output conector with Molex Clik-Mate 4p.
Blue power "ON" LED.
59mm x 66mm x 1..
179.90€
Ex Tax:147.46€
Brand: Gremsy
Model: GR-S1-UBEC
A switching power supply that has dual outputs (12V-5A, 5V-1A) and accept wide input range from 14V to 52V, comes in a small and lightweight module. This UBEC should be used with the S1 where power for camera and accessories is needed on the tilt stage of the gimbal. Connect output of the UBEC to th..
79.90€
Ex Tax:65.49€
Brand: Mauch Electronic
Model: MAU2-017
Input 4-6S LiPo / max. 28V.
Output 2x 5.35V / 3A + 1x 12.0V / 3A -> +/- 0.05V –> Ripple 10mV (0.2%) at 1.5A output current.
Inclusive LDO power supply (+5.00V +/- 0.03V) for the sensor board PL-xxx as well as PL- Sensor Hub X2 and output conector with Molex Clik-Mate 4p.
Input wrong polarity protec..
94.90€
Ex Tax:77.79€
Brand: Mauch Electronic
Model: MAU2-023
Mauch 4-14S HYB-BEC 5.30V 3A Output Suit Pixhawk 2 Backup BEC
Mauch BEC"s are built the the highest quality and each unit is carefully tested before shipping. These are made to connect directly to the Pixhawk 2 Autopilot as a backup BEC. Due to the highest quality components the BEC runs only warm u..
179.90€
Ex Tax:147.46€
Brand: Mauch Electronic
Model: MAU2-021
Input 4-14S LiPo / max. 60V.
Output 5.30V / 3A -> +/- 0.05V –> Ripple 1mV @ 1.5A output current.
Inclusive LDO power supply (+5.00V +/- 0.03V) for the sensor board PL-xxx as well as PL- Sensor Hub X2/X8 and output conector with Molex Clik-Mate 4p.
Blue power "ON" LED.
59mm x 29mm x 13mm / 26..
74.90€
Ex Tax:61.39€