![DJI Mini 3 Pro [image]](https://www.onedrone.com/store/image/cache/catalog/banners/dji_mini_3_pro_no_rc_-550x550w-200x120w.jpg)
-150x150h.jpg)
-1000x1000-150x150.jpg)
-150x150.png)
Search Criteria
Products meeting the search criteria
Model: LC-SRBEAST-TOP-PLATE
Replacement Top Plate for SR-Beast by Lethal Conception.
Sold by one..
16.90€
Ex Tax:13.85€
Model: DFRSOURCEV5-MIDDLE
Middle plate for the DFR Source One 5" V5 frame.
Specifications
Thickness : 2mm
Weight : ~11.1g
Included
1x Middle plate
8x M3 pressnut
Voir plus..
4.90€
Ex Tax:4.02€
Model: 21672
Front split plate intended for QAV-S 2 JohnnyFPV SE frames from Lumenier.
Specifications
Compatibility : QAV-S 2 JohnnyFPV SE 5-7inch
Thickness : 3mm
Orientation : Front
Included
1x Front Split plate
Voir plus..
15.90€
Ex Tax:13.03€
Model: H7A3-SLIM
The Matek H7A3-SLIM flight controller is equipped with a SPL06-001 barometer, an AT7456E OSD, 6 UARTs and has a USB type C output.
Specifications
MCU: STM32H7A3RIT6, 280MHz Cortex-M7, 1.4MB RAM, 2MB Flash
IMU: ICM42688P
Baro: SPL06-001
OSD: AT7456E
Blackbox: 128MB Flash (1G-bit NAND)
6x Uarts ..
77.90€
Ex Tax:63.85€
Model: PM20S-2
The PM20S module has a wide operating input range of 9 to 85V with TVS protection.
With a weight of 63g, it is made with 100V DC components.
Specifications
PM20S-2 is made with 100V DC components.
Support 9V to 85V DC operating Input voltage with 85V TVS protection
2x independent Step-Down Vol..
68.90€
Ex Tax:56.48€
Model: CAN-G474
Matek"s CAN-G474 is a Node adapter based on ArduPilot AP-Periph firmware.
With this board, you will be able to more easily use ArduPilot to convert GNSS, Compass, barometers, airspeed sensor, PWM and buzzer devices to DroneCAN devices.
CAN-G474 has STM32G474 chip and 5Mbit/s transceiver.
Spec..
24.90€
Ex Tax:20.41€
Model: CANPDB-4A
This CANPDB from Matek will allow you to plug four CAN devices into one plug.
*Power and distance are subject to specific regulations, be sure to respect those established in the country where you are playing.
Specifications
6V to 55V Operating Input Range(2S-12S Li-xx)
5.2V output on “5V” p..
18.90€
Ex Tax:15.49€
Model: BCNFI2
Fly ID is a direct remote identification device compatible with all drones.
It is equipped with the EASA DRI (Direct Remote ID) system compliant with the prEN 4709.002 standard in compliance with the regulations in force in Europe for homemade drones and modelers.
The beacon will transmit the ident..
116.90€
Ex Tax:95.82€
Model: 209-8140
This 422C tropicalizer is mainly used to protect your electronic components from humidity, corrosion, dirt and dust.
This will allow you to fly in wet conditions with more confidence.
In case of light rain, snow, condensation or landing on wet grass, the 422C will protect your drone.
However, the tr..
29.90€
Ex Tax:24.51€
Model: JH61223
Here is the Stack Mamba Basic F405 MK2 V2 55A from Diatone.
It consists of an MPU6000 gyro, a 16Mb blackbox, an AT7456E OSD and is mounted in 30.5x30.5mm.
Upon receiving your FC,please connect to USB and calibrate before continuing to build and solder to it.
F405 MK2 V2 FC
MCU: STM32F405
Frequ..
93.90€
Ex Tax:76.97€
Model: NMB-BEARING-NT
This set of 10 NMB 9x4x4 bearings will allow you to replace those that are too worn in your motors starting to squeak a little too much over crashes with humidity.
Compatible with a large majority of 5" motors, remember to measure your current bearings using a caliper to be sure of the correct sizin..
20.90€
Ex Tax:17.13€
Model: *CAN-L4-RC
This L4 RC CAN adapter from Matek is based on the ArduPilot AP_Periph firmware and allows you to turn a serial receiver into a CAN receiver.
Specifications
MCU: STM32L431xC, 256KB Flash
1x CAN, DroneCAN Protocol
1x UART(UART3, Tx3/ Rx3)
ST debug, SWCLK & SWDIO
Input voltage range: 4.5~5.5V @..
15.90€
Ex Tax:13.03€