![DJI Mini 3 Pro [image]](https://www.onedrone.com/store/image/cache/catalog/banners/dji_mini_3_pro_no_rc_-550x550w-200x120w.jpg)
-150x150h.jpg)
-1000x1000-150x150.jpg)
-150x150.png)
Search Criteria
Products meeting the search criteria
Model: pixtele
Improving range of telemtrz for 3 times or more.Right-angle SMA connector with a piano-wire whip, flexible enough to survive some serious abuse...
5.90€
Ex Tax:4.84€
Model: BALANCER-XH-KIT-DIY
Practical and complete, this kit of cables and connectors will allow you to repair your lipo balancing plugs.
This kit contains 10 XH plugs for each type of lipo (6S/5S/4S/3S/2S).
The red and black cables supplied are already pre-crimped to facilitate the creation of your "custom" balancing socket,..
21.90€
Ex Tax:17.95€
Model: JST-XH-ADAPTER
Balance board adapter for batteries with EH balance plug. For lithium batteries 2 to 6 elements...
5.90€
Ex Tax:4.84€
Brand: FrSky
Model: JST-XH-TO-XT60
This adapter lead converts from a 2S Balance Plug (JST-XH) to a Female XT60. You can use it to charge a FrSky NiMH battery, such as that which comes with the Taranis QX7s radio with your RC Smart Charger on the appropriate NiMH setting. ..
4.90€
Ex Tax:4.02€
Model: XH-MALE
Connector balancer with wires 22awg
3/4/5 and 6S available
Sold individually...
1.90€
Ex Tax:1.56€
Brand: Mauch Electronic
Model: MAU2-085
This BEC is an switching power supply and in series an linear LDO (LM1764A) to remove the ripple. Due to the component selection, this BEC get"s only warm during operation (LDO only 0.35V dropout voltage).
Input and output is protected by Panasonic FC / FM capacitors.
Input 4-14S LiPo / max. 60V.
Ou..
55.90€
Ex Tax:45.82€
Brand: Mauch Electronic
Model: MAU2-083
Input 2-6S LiPo / max. 28V.
Output 5.35V / 3A -> +/- 0.05V –> Ripple 10mV (0.2%) at 1.5A output current.
Input wrong polarity protection, as well as Panasonic FM input and output capacitors to prevent burn out of the UBEC from voltage spikes.
20cm output cable with Molex / 6p / Clik-Mate 2.0mm. (To ..
31.90€
Ex Tax:26.15€
Brand: Mauch Electronic
Model: MAU2-042
This cable is for the PL 2-6S series BEC"s to connect to Pixhawk 2.1 or any flight controller with Molex / Clik-Mate / 2.0mm / 6p connector.
L = 150mm ..
7.90€
Ex Tax:6.48€
Brand: Mauch Electronic
Model: MAU2-041
This cable is for the PL 2-6S series BEC"s to connect to any flight controller with DF13-6p connector.
For example:
Pixhawk 1, APM... etc.
L = 150mm ..
5.90€
Ex Tax:4.84€
Brand: Mauch Electronic
Model: MAU2-088
Mauch Standard Line Customized cable from HS-xxx-xx Sensor Board to Pixhawk / APM
The cable is made of AWG28 silicone wires with original Hirose DF13 connectors.
The total cable length should not exceed 290mm.
The cables are "hand made" and electrical tested.
If no requested cable length is provided..
5.90€
Ex Tax:4.84€
Brand: Mauch Electronic
Model: MAU2-043
This cable is for the PL 2-6S series BEC"s to connect to any flight controller with JST-GH 6p connector.
For example:
Pixhawk 3, PixRacer... etc.
L = 150mm ..
7.90€
Ex Tax:6.48€
Model: MAU2-061
Power-Cube / Pixhawk 2.1 Backup / 2x C-M-6P + 1x JR / 200mm
To connect Power-Cube output 2 to Pixhawk 2.1 Power 2 connector as backup.
The JR connector can be connected to the servo rail to power up opto ESC"s or any other equipment.
REM: This cable is standard delivery with Power-Cube 2, 3, and 4 !..
8.90€
Ex Tax:7.30€