![DJI Mini 3 Pro [image]](https://www.onedrone.com/store/image/cache/catalog/banners/dji_mini_3_pro_no_rc_-550x550w-200x120w.jpg)
-150x150h.jpg)
-1000x1000-150x150.jpg)
-150x150.png)
Search Criteria
Products meeting the search criteria
Model: MT-ASPD-DLVR
Matek Digital Airspeed Sensor ASPD-DLVR
All sensors DLVR series is the best airspeed sensor ArduPilot currently support.
Specifications & Features• ArduPilot AP_Periph L431/F405/F303 CAN node• All sensors DLVR-L10D, Industrial temperature range• CAN & I2C Interface• Typical Platforms: Fixed-Wing, Qu..
129.90€
Ex Tax:106.48€
Brand: Mauch Electronic
Model: MAU2-086
The cable is made of AWG28 silicone wires with original Hirose DF13 and MOLEX / Clik-Mate 2.0mm connectors.
The total cable length should not exceed 290mm.
The cables are "hand made" and electrical tested.
If no requested cable length is provided, then we will deliver the standard length of 200mm ..
8.90€
Ex Tax:7.30€
Brand: Gremsy
Model: GR-MIO-PCC-FD
The cable is designed to supply 12V power and transmit the Mavlink signal from Pixhawk controller to Flir Duo Pro R through Mio Gimbal..
41.90€
Ex Tax:34.34€
Brand: Gremsy
Model: GR-MIO-PCC-FV
The cable is designed to supply 12V power and transmit the control signal from the controller to Flir Vue Pro R through Mio Gimbal.
Support only for the Flir Vue Pro R using with Flir Power & HDMI module...
41.90€
Ex Tax:34.34€
Hot
Brand: ProfiCNC/HEX
Model: HX-IR-CAB
Connect your IR-LOCK Sensor to the Cube autopilot. This cable provides I2C communication from IR-LOCK to the Cube via the Carrier Board, and also powers the IR-
LOCK Sensor. Length: 28cm See Documentation for connection instructions...
9.90€
Ex Tax:8.11€
Brand: Gremsy
Model: GR-P-CL
To connect from port on the PIXY F to TELEMETRY1/2 port on PIXHAWK 2.
Specs:
Cable length: 30cm..
27.90€
Ex Tax:22.87€
Brand: Gremsy
Model: GR-T3-P2
Gremsy T1/T3 - Canlink Cable for Pixhawk 2
To connect from COM2 port on the T1 to TELEMETRY1/2 port on PIXHAWK 2.
Lenght: 30cm..
16.90€
Ex Tax:13.85€
Model: RFD-P-2
Power supply for RFD Series 868, 900, 868x, 900x for Pixhawk 2
If you connect direclty RFD it can burn/spike your Pixhawk cause RFD can draw to much mAmps, so you need to connect it through BEC.
This is 4-6S version plug and play, but we can make it 12S too...
43.90€
Ex Tax:35.98€
Brand: Matek
Model: RTS-ASkit-Pix
The Matek Digital Airspeed Sensor ASPD-4525 features a ASPD-4525 sensor board, JST-GH to JST-GH 20cm silicon cable, pitot tube and a clear silicon tubing (40cm) to help monitor your wing"s airspeed !
Specifications• Board Supply voltage: 4~5.5V DC• Sensor: MS4525DO• Working current: 5mA• Output: I2C..
64.90€
Ex Tax:53.20€
Model: pixtele
Improving range of telemtrz for 3 times or more.Right-angle SMA connector with a piano-wire whip, flexible enough to survive some serious abuse...
5.90€
Ex Tax:4.84€
Brand: Mauch Electronic
Model: MAU2-085
This BEC is an switching power supply and in series an linear LDO (LM1764A) to remove the ripple. Due to the component selection, this BEC get"s only warm during operation (LDO only 0.35V dropout voltage).
Input and output is protected by Panasonic FC / FM capacitors.
Input 4-14S LiPo / max. 60V.
Ou..
55.90€
Ex Tax:45.82€
Brand: Mauch Electronic
Model: MAU2-083
Input 2-6S LiPo / max. 28V.
Output 5.35V / 3A -> +/- 0.05V –> Ripple 10mV (0.2%) at 1.5A output current.
Input wrong polarity protection, as well as Panasonic FM input and output capacitors to prevent burn out of the UBEC from voltage spikes.
20cm output cable with Molex / 6p / Clik-Mate 2.0mm. (To ..
31.90€
Ex Tax:26.15€