Menu
Your Cart

Mauch Electronic

Brand: Mauch Electronic Model: MAU2-080
This sensor hub is to connect two Standard Line (HS) current sensors in parallel. The current of both sensors will be summarized and passed to the FC. The voltage measurement of the LiPo packs will be collected from both sensors and passed through the Hub to the FC. The main purpose of this hub is t..
59.90€
Ex Tax:49.10€
Brand: Mauch Electronic Model: MAU2-076
200A - Current measurement sensor board, based on Allegro Hall Sensor ACS-200U.  The voltage reading of the LiPo is optimised for up to 14S LiPo packs.  This Sensor board needs a power supply. So please select the matching BEC according your preference from the BEC section.  The BEC will also power ..
57.90€
Ex Tax:47.46€
Brand: Mauch Electronic Model: MAU2-074
100A - Current measurement sensor board, based on Allegro Hall Sensor ACS-100U.  The voltage reading of the LiPo is optimised for up to 14S LiPo packs.  This Sensor board needs a power supply. So please select the matching BEC according your preference from the BEC section.  The BEC will also power ..
54.90€
Ex Tax:45.00€
Brand: Mauch Electronic Model: MAU2-023
Mauch 4-14S HYB-BEC 5.30V 3A Output Suit Pixhawk 2 Backup BEC Mauch BEC"s are built the the highest quality and each unit is carefully tested before shipping. These are made to connect directly to the Pixhawk 2 Autopilot as a backup BEC. Due to the highest quality components the BEC runs only warm u..
179.90€
Ex Tax:147.46€
Brand: Mauch Electronic Model: MAU2-021
Input 4-14S LiPo / max. 60V. Output 5.30V / 3A -> +/- 0.05V –> Ripple 1mV @ 1.5A output current. Inclusive LDO power supply (+5.00V +/- 0.03V) for the sensor board PL-xxx as well as PL- Sensor Hub X2/X8 and output conector with Molex Clik-Mate 4p. Blue power "ON" LED. 59mm x 29mm x 13mm / 26..
74.90€
Ex Tax:61.39€
Brand: Mauch Electronic Model: MAU2-022
Input 4-14S LiPo / max. 60V.  Output 2x 5.30V / 3A -> +/- 0.05V –> Ripple 1mV @ 1.5A output current. Inclusive LDO power supply (+5.00V +/- 0.03V) for the sensor board PL-xxx as well as PL- Sensor Hub X2/X8 and output conector with Molex Clik-Mate 4p. Blue power "ON" LED. 59mm x 48mm x 13mm / 41g w..
119.90€
Ex Tax:98.28€
Brand: Mauch Electronic Model: MAU2-001
50A - Current / Voltage measurement sensor board, based on Allegro Hall Sensor ACS758-050U. Voltage range is up to 14S (60V) with solder bridge open and up to 7S (30V) with solder bridge closed. Please check the maual page for more details. This Sensor board connects directly to any Premium-Line BEC..
54.90€
Ex Tax:45.00€
Mauch Power Cube 2 / v3 (1x5V 1x12V)
Out of stock
Brand: Mauch Electronic Model: MAU2-052A
Input voltage 3-20S, max. 85V !  Power-Cube 2 / V2 with 2 outputs 1x 5.3V / 10A + 1X 12V. REM: The output voltage can be customized. Please mention in the required Voltage at NOTE in order, if you need a different output voltage on output 2 -> Output 1 can"t be changed and must remain 5.3V. Delivery..
240.90€
Ex Tax:197.46€
Brand: Mauch Electronic Model: MAU2-081
3D printed enclosure for the Sensor Hub X2  The enclosure should be installed with double side tape (included). The Sensor Hub X2 will just “click” into the bottom part and the top should be secured with any ABS (Acetone) glue or Cyanoacrylate (super) glue. REM: It is the nature of 3D printed parts,..
7.90€
Ex Tax:6.48€
Brand: Mauch Electronic Model: MAU2-013
The Sensor Hub X8 collects the current measurements from up to eight Power-Cube current sensors. The currents are summed up and passed to the Pixhawk flight controller via the Power-Cube power supply. The voltage measurement of the LiPo packs is measured separately by the Power-Cube. An OLED display..
199.90€
Ex Tax:163.85€
Brand: Mauch Electronic Model: MAU2-084
This BEC is an switching power supply and in series an linear LDO (LM1764A) to remove the ripple. Due to the component selection, this BEC get"s only warm during operation (LDO only 0.35V dropout voltage).  Input and output is protected by Panasonic FC / FM capacitors. Input 4-14S LiPo / max. 60V . ..
52.90€
Ex Tax:43.36€
Brand: Mauch Electronic Model: MAU2-085
This BEC is an switching power supply and in series an linear LDO (LM1764A) to remove the ripple. Due to the component selection, this BEC get"s only warm during operation (LDO only 0.35V dropout voltage). Input and output is protected by Panasonic FC / FM capacitors. Input 4-14S LiPo / max. 60V. Ou..
55.90€
Ex Tax:45.82€
Showing 13 to 24 of 45 (4 Pages)