



















- Stock: Out of stock
- Model: SB-F405WING-MINI
This product is not available. You can fill out the form below to be notified when the product will be available again.
The F405 WING Mini flight controller from SpeedyBee is intended for airplanes as well as FPV quads.
Compatible with most HD and analog VTXs, this FC consists of an STM32F405 processor, an ICM-42688P gyroscope, an SPL006-001 barometer, an AT7456E OSD as well as 6 UARTS.
In addition to supporting INAV and ArduPilot, the F405 WING Mini allows you to configure it from the SpeedyBee and QGroundcontrol applications.
An integrated switch gives you the possibility of switching from one analog camera to another to benefit from more viewing angles.
Optimal heat dissipation, TVS protection diode, current sensor and buzzer are features that will ensure safety.
F405 WING Mini FC
- MCU : STM32F405, 168MHz, 1MB Flash
- IMU(Gyro&Accelerometer) : ICM-42688-P
- Barometer : SPL006-001
- OSD Chip : AT7456E
- Blackbox : MicroSD Card Slot
- UART : 6 sets (USART1, USART2, USART3, UART4, UART5, UART6 - Dedicated for Wireless board Telemetry connection)
- I2C : 1x Used for magnetometer, digital airspeed sensor
- ADC : 4x (VBAT, Current, Analog RSSI, Analog AirSpeed)
- PWM : 12x (9x pin headers + 2x solder pads + 1x "LED" pad)
- ELRS/CRSF Receiver : Supported, connected to UART1
- SBUS : Built-in inverter for SBUS input (UART2-RX)
- LED : 3x LEDs for FC STATUS (Blue, Green) and 3.3V indicator (Red)
- Analog RSSI : Supported, Named as "RS"
- Dual Analog Camera Switching : Default to Camera1 Video Input (C1). Switch between C1 and C2 using ArduPilot Relay or INAV Modes/USER. Both cameras should have the same video format, either PAL or NTSC.
- Supported FC Firmware : INAV: SpeedyBeeF405WING (default) / ArduPilot : SpeedyBeeF405WING
- Weight : 5.6g
PDB
- Input voltage range : 7~26V (2~6S LiPo)
- Battery Voltage Sensor : Connect to FC board VBAT, 1K:10K (Scale 1100 in INAV, BATT_VOLT_MULT 11.0 in ArduPilot)
- Battery Current Sensor : 80A continuous, 150A peak Connect to FC board Current (Scale 195 in INAV, 50 A/V in ArduPilot)
- TVS Protective diode : Yes
- FC BEC output : Output 5.2V +/- 0.1V DC Continuous current 2 Amps, 3A Peak Designed for FC, Receiver, GPS module, AirSpeed Sensor, Telemetry module
- Servo BEC output : Output 5V +/- 0.1V DC Continuous current 4 Amps, 5A Peak Voltage adjustable, 5V Default, 6V via jumper Designed for Servos.
- Weight : 5.5g
Included
- 1x F405 WING Mini
- 1x 90 Degree pin header (3x10)
- 3x Straigth pin header (1x10)
- 5x M2x6.5 copper standoff spacer
- 10x M2x3.5 small head cross screw
- 1x White straigth pin header (1x4)
- 5x M2x3+3 copper standoff spacer
- 1x 35V 470uF Low ESR Capacitor
- 1x 8pin SH1.0mm USB extender cable
- 1x 4pin SH1.0mm Analog VTX cable
- 1x 6pin SH1.0mm GPS module cable
- 1x 6pin SH1.0mm HD VTX cable
- 1x 4pin SH1.0mm to 3pin JST1.25mm FPV cam cable
- 1x 4pin Dupont single head cable
Find the product you want and add it to your cart. A window will open, offering you two options - to continue shopping or to complete the purchase. Choose what suits you.
When you have selected everything you need, carefully examine the basket, then click on the "continue to enter information" button. Choose from the options: natural or legal person. First, you will need to enter information, depending on whether you are a natural person or a company. If you are ordering or buying as a legal entity, i.e. a company registered in Slovenia as well as the EU, you must enter the following:
- Company name
- The exact address of the company
- tax number
- Mandatory phone number (delivery service)
Choose a payment method:
- In summary
- TRR
- Paypal
- Leanpay
At the very end, carefully read the information about your order and confirm your choice.
The package will arrive at your address within 1-3 working days.
Products are delivered by the GLS delivery service. Upon delivery, the delivery man of the GLS delivery service will call you and arrange with you to pick up the package. The package will be delivered to the address you specified when ordering.
You can choose between three payment methods:
- Via the online bank or according to the estimate
- PayPal*
- Cash on delivery
- Lean pay
If the value of the package is less than €50, delivery within Slovenia via the delivery service is €5.90. For purchases over €50, delivery within Slovenia is free.
The delivery amount is calculated at the end of the purchase.
Unfortunately, discounts and benefits in our online store do not add up. You can only use one discount code per order.
If you want to go through the return process, we kindly ask you to fill out the form here.
If, within 15 days of purchase, the customer finds that he does not want the product for any reason, he must bring the product to us in its original packaging, undamaged, UNACTIVATED with the invoice. In such a case, we return the purchase price to the customer.
If within 15 days of purchase the customer finds that there is something wrong with the product (drone), bring the product to us or you return it in the original packaging with all the contents that were in it. In such a case, we replace the customer's drone with a new one. The product can be returned in its original packaging, undamaged, with a receipt.
After 15 days, the warranty process expires. We send the product to a DJI authorized official service center. We receive the replaced product within 7-10 working days.
The warranty starts from the activation of the drone and not from the purchase of it. You do not need an account to claim the warranty.
Service at an authorized DJI drone service center takes 7-10 working days. Because DJI has high safety standards, they exchange drones for new ones and do not repair them.
Yes, you can visit our store, where we will be happy to help you and present the product.
To rent products, please go to our website:rent.onedrone.com/storeor visit our store.
Contact us and we guarantee that you will receive all the necessary information.
Call us at the number:041 688 150
But contact us via e-mail:info@onedrone.si