![DJI Mini 3 Pro [image]](https://www.onedrone.com/store/image/cache/catalog/banners/dji_mini_3_pro_no_rc_-550x550w-200x120w.jpg)
-1000x1000-150x150.jpg)
-150x150.png)
Novo
Ni na zalogi
Model: 010-0154-00
The Castle Creations CC BEC 2.0 is the power solution for cinelifters video system.
The latter will give you higher voltage ranges.
This voltage regulator is perfect for powering servos, cameras and other power-hungry accessories.
The CC BEC 2.0 is the solution to protect your electronic components ..
61.90€
Brez DDV:50.74€
Blagovna znamka: Mauch Electronic
Model: MAU2-082
Input 2-6S LiPo / max. 28V.
Output 5.35V / 3A -> +/- 0.05V –> Ripple 10mV (0.2%) at 1.5A output current.
Input wrong polarity protection, as well as Panasonic FM input and output capacitors to prevent burn out of the UBEC from voltage spikes.
20cm output cable with Molex / 6p / Clik-Mate 2.0mm. (To ..
26.90€
Brez DDV:22.05€
Model: HM-SB
HiModel 6-50V Input 20A Large Current Switching Mode Voltage Regulator/ SBEC
HiModel 20A SBECInput: 6 - 50.4 VOutput voltage: 7.4V 8.4V 9V 12V OUTPUT (jumper selection)Current: 20amps continuous/ 25amps peak (2 seconds)Mode: Switch-modeQuiescent current: 60uA to 200uASize: 45 x 26 x 8mmWeight: 30g..
36.90€
Brez DDV:30.25€
![APD PowerBoard PDB360[X] 8S 34V 360A](https://www.onedrone.com/store/image/cache/catalog/produkti/APD-PD360/apd-pdb360-250x250.jpg "APD PowerBoard PDB360[X] 8S 34V 360A")
Blagovna znamka: APD
Model: APD-PD360
The APD PDB360 is designed for high voltage and high current applications. It consists of 8 layers of heavy copper to sustain maximum current demand whilst dissipating minimal heat. This PDB can sustain up to 90A continuous to each ESC leg. Also features 12V 3Amp and 5V 1Amp regulators with a maximu..
45.90€
Brez DDV:37.62€
Ni na zalogi
Model: KW-BEC-6S
High Quality, small and light 5V/12V 3A UBEC Support 2-6S/3-6S Lipo Battery Fully Shielded Anti-interference Voltage Stabilizer in Alu housing
Move switch on the side, switch between two output voltages: 5V or 12V
Input voltage: 7-28V (2-6S)Current output: 3AOutput voltage: 5V/12V (switch)Operating ..
14.90€
Brez DDV:12.21€
Blagovna znamka: Gremsy
Model: GR-P-UBEC
A switching power supply that has dual outputs (12V-5A) and accept wide input range from 14V to 52V, comes in a small and lightweight module. This UBEC should be used with the PIXY where power for Flir Duo Pro R via the AUX 8-pin cable on the tilt cage. ..
81.90€
Brez DDV:67.13€
Ni na zalogi
Blagovna znamka: Mauch Electronic
Model: MAU2-031
This new PC Series PDB includes two fully redundant BEC’s with POWER1 and POWER2 for the FC.
All in one PDB for Pixhawk 2.1 (The Cube) and any other flight controller via adapter cable. With integrated 2x200A hall sensor, Sensor Hub X2, 4-14S HYB-BEC and most important an main power switch with an c..
619.90€
Brez DDV:508.11€
Ni na zalogi
Model: HK-SB-12S
The all new Multistar twin output SBEC is an advanced switching DC-DC regulator designed specifically with multirotors in mind.It will simultaneously supply a constant 5Amps at 5V and 10Amps at 12V. It works with 2-13 cell lipoly packs and supplies an interference free constant 5V to your receiver a..
36.90€
Brez DDV:30.25€
Blagovna znamka: Mauch Electronic
Model: MAU2-025
Input 4-14S LiPo / max. 60V.
Output 2x 5.30V / 1x 5.0V / 1x 12.0V / 3A -> +/- 0.05V –> Ripple 1mV @ 1.5A output current.
Inclusive LDO power supply (+5.00V +/- 0.03V) for the sensor board PL-xxx as well as PL- Sensor Hub X2/X8 and output conector with Molex Clik-Mate 4p.
Blue power "ON" LED.
59mm x..
229.90€
Brez DDV:188.44€
Blagovna znamka: Mauch Electronic
Model: MAU2-024
Input 4-14S LiPo / max. 60V.
Output 2x 5.30V / 1x 12.0V / 3A -> +/- 0.05V –> Ripple 1mV @ 1.5A output current.
Inclusive LDO power supply (+5.00V +/- 0.03V) for the sensor board PL-xxx as well as PL- Sensor Hub X2/X8 and output conector with Molex Clik-Mate 4p.
Blue power "ON" LED.
59mm x 66mm x 1..
179.90€
Brez DDV:147.46€
Ni na zalogi
Blagovna znamka: Gremsy
Model: GR-S1-UBEC
A switching power supply that has dual outputs (12V-5A, 5V-1A) and accept wide input range from 14V to 52V, comes in a small and lightweight module. This UBEC should be used with the S1 where power for camera and accessories is needed on the tilt stage of the gimbal. Connect output of the UBEC to th..
79.90€
Brez DDV:65.49€