Seriously Pro Racing F3 Flight Control Acro 6DOF (NAZE32 Upgrade Version) for Multicopter

  • OneDrone
  • OD-naze-f3
  • 40
  • 8
  • 39.91€

  • Ex Tax: 32.71€
- OR -



Item Name: SP Racing F3 Flight Control NAZE32 Upgrade Version for Multicopter Acro Version

Version: Acro 6DOF * 36x36mm board, 30.5 mm mounting holes.

* STM32F3 CPU.

* High-capacity Flash (Acro 6DOF)

 * MPU6050 Accelerometers and Gyroscopes

 * MicroUSB socket.

 * 4 x 4 pin JST-SH Socket (I2C, SWD, 2xuart)

* 2 x 8 pin JST-SH Socket (PPM, PWM, SERIAL RX, GPIO, ADC, 3V, 5V, GND)

* 8 x 3 pin though-holes for pin headers for ESC / Servo connections.

 * 2 x 4 pin though-holes for the 2x serial ports .

* 2 x 2 pin though-holes for battery voltage and buzzer.


Features: Better coding practices and introducing tests, easier to maintain and for future development. (Dominic has software development background) Many bugs fixed from Baseflight.

Supports more flight controllers, including CC3D, CJMCU and Sparky.

Supports OneShot ESC and more than 8 RC channels.

Additional PID controllers that uses floating point arithmetic operations. (now has 3 built-in PID Controllers)

Many more features such as RGB LED strip support, Autotune, In-flight PID tuning with your radio, blackbox flight data logging etc.


Flight Performance

The SPR F3 builds on tried and tested software, processor and sensor technology to make your aircraft fly like it's on


No-Compromise I/O

Use all the features all the time; e.g. Connect your OSD + SmartPort + SBus + GPS + LED Strip + Battery Monitoring + Sonar + 8 motors - all at the same time!


The SP F3 runs Cleanflight which can be configured to suit your needs using a cross-platform GUI (Windows/OSX/Linux).

Tiny and lightweight

The RacingF3 has a standard 36x36mm form-factor with 30.5mm mounting holes and weighs just 6 grams.

Flight Logging

On-board high-capacity black box flight log recorder - optimize your tuning and see the results of your setup without guesswork.

Next-Generation CPU

The RacingF3 has an ARM Cortex-M4 72Mhz CPU with Math co-processor (FPU) for efficient flight calculations that gets more done in less time. Loop times up to ~2x as fast as previous-generation STM32F1 based boards.

Developer Friendly

Developer friendly debugging port (SWD) and boot mode selection, unbrickable bootloader.

OneShot ESC

Full support for OneShot ESCs for easy PID tuning and a sharper response.

Broad RC receiver Support

Supports SBus, SumH, SumD, Spektrum1024/2048, XBus, PPM, PWM receivers. No external inverters required (built-in).


LED Dedicated output for programmable LEDs - great for orientation, racing and night flying.

Battery Monitoring

Battery monitoring ports for voltage and current.


Sonar support for precision low-altitude hold.

I2C Port

I2C port always powered, perfect for external sensors or always-on OLED Screen.


Buzzer port for audible warnings and notification


Please refer to the following link for PC Interface and Drive


Package Includes:

Acro 6DOF Version

1 x Upgrade NAZE32 SP Racing F3 Flight Control for Multicopter
2 x 8p Wire Rod

2 x 4p Extension Path

4 x Pins set

Write a review

Note: HTML is not translated!
    Bad           Good
Related Products